Page 1 of 1

Trap electronics needed in uk

Posted: December 2nd, 2022, 7:26 am
by Colin1980
Hi all
Iam just on the looking for the electrics
For a trap ive tryed to make it my self but with
No luck
Iam in the uk in Lincolnshire
Thanks guys

Re: Trap electronics needed in uk

Posted: December 4th, 2022, 3:37 am
by tobycj
Ghost Mech 852 on Facebook does them. They're not cheap, but are great.

Re: Trap electronics needed in uk

Posted: December 4th, 2022, 5:34 pm
by Colin1980
Thanks buddy

Re: Trap electronics needed in uk

Posted: December 7th, 2022, 9:28 am
by Colin1980
He dont seem to be msg me bk
Anyone eles in the uk
Ive tryed makeing one and its not working
So ive gave up lol

Re: Trap electronics needed in uk

Posted: December 7th, 2022, 9:58 am
by tobycj
Charlesworth Dynamics on etsy sells his trap electronics plans, but they're full on DIY, rather than buying a PCB that's plug and play. There's a couple of other folk developing kits (both in the US though), but they're a way off being sold yet. I'd drop Ghost Mech 852 another message, and hopefully he'll get back to you soon.

Re: Trap electronics needed in uk

Posted: December 7th, 2022, 11:59 am
by Colin1980
Ive tryed makeing Charlesworth Dynamics
One i have all the parts just can't seem to get it to work lol

Re: Trap electronics needed in uk

Posted: December 8th, 2022, 1:07 pm
by Colin1980
He msg me bk
Wants about £380 just for the electronics
Way to expensive

Re: Trap electronics needed in uk

Posted: December 8th, 2022, 3:39 pm
by Kingpin
Colin1980 wrote: December 8th, 2022, 1:07 pm Wants about £380 just for the electronics
Way to expensive
While that is higher than some, unfortunately electronics kits do have a tendency to be expensive... And that was before the chip shortage pushed prices up.

Re: Trap electronics needed in uk

Posted: December 8th, 2022, 6:08 pm
by prodestrian
Colin1980 wrote:Ive tryed makeing Charlesworth Dynamics
One i have all the parts just can't seem to get it to work lol
I've seen you post this in 3 different places, but you haven't actually said why it doesn't work.
Where did you get up to? Did you get any of it working? Is there a part you're really stuck on?

It'd be a shame to buy all those parts and give up, only because you have a wire the wrong way around or one of the parts was delivered defective.

Jump into the Arduino for Ghostbusters Props group on Facebook and post some photos and details. Maybe we can help, maybe not. But it's worth a shot, right?

As a software engineer, I can tell you right now that "it doesn't work" is the least helpful phrase in troubleshooting.
Whereas something like "I plug it in and the red light flashes 3 times then it completely freezes"...we can work with that! :-D

Also Joseph Lavender has recently released some video tutorials about Arduino Proton Packs, it's possible we can point you to some clips which also apply to the Charlesworth Trap electronics.

Re: Trap electronics needed in uk

Posted: December 9th, 2022, 1:41 am
by Colin1980
Ok buddy
Well ive put all the code and Library on the arduino and the mp3 on the sd card check all the wires like 5 times they fine and all i get is a low buzzing off the mp3 player ive checked its getting 5v
Ive unplug every thing to see if anything was stopping the mp3 player from working andstill the same thing

Re: Trap electronics needed in uk

Posted: December 9th, 2022, 1:45 am
by Colin1980
And ive got a new arduino and new mp3 player
Just in case so well try again

Re: Trap electronics needed in uk

Posted: December 9th, 2022, 9:51 am
by Colin1980
Got the new sound board going powers up but dont play the sounds that are on the sd card juat beeps

Re: Trap electronics needed in uk

Posted: December 11th, 2022, 12:42 pm
by Colin1980
Think its the sd card so ive ordered a new one
See if that helps

Re: Trap electronics needed in uk

Posted: December 11th, 2022, 12:57 pm
by prodestrian
Which MP3 player does it use?
You're right, it could definitely be the SD card. But for some MP3 players it can also be the way the card is formatted or how the files are copied over.

I think you're already making progress here!

I also believe there may be a gbfans thread where someone updated and improved Sean's Arduino code, but I'd have to dig around to find it.

Re: Trap electronics needed in uk

Posted: December 12th, 2022, 7:32 am
by Colin1980
Its going well i got a new sd card and how its playing sound and the led are working so how i need to sort out the bar graph