This is for other Ghostbusters Props that don't fit into the categories above.
User avatar
By GhostbusterRN
#4974527
This post may contain an affiliate link that helps support GBFans.com when you make a purchase at no additional cost to you.

Image

Image

Image


https://youtu.be/Zd58ELAreBc

Now I may be missing sound and I will make the interior more accurate soon, but far as I have seen on here mine is the only movie accurate light sequence, Salt Lake Ghostbusters is super close but when you click the red button and then the yellow the red button light should go off but theirs stays on.

Here’s is my Ecto Containment Unit. I used Southland, and Salt lake Ghostbusters ECU’s as examples. Mine is made almost completely of FOAM!!! That’s right construction foam, you can see in the pics how it went. I made it functional by reinforcing with dowel rods, and styrene plastic for areas where hardware was used.

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image

Image
This panel of styrene was added so the handle had something strong on the outside to allow the handle to be fastened to, then I used wood filler and painted it to hide it some.
Image

Image

Image

Image

Image

Image

Image

My build list:
-1 inch Construction foam 2- 4x8 sheets, one cut in half to fit in the truck and the other 1/4 was cut off, if you cut it in half you can’t make the large back section it won’t be big enough.
-Clear Gorilla Glue (this is non expanding)
-Dowel rod pieces
-Masonite board (peg board with no holes)
-wood filler to hide seams
-Jack chain to hold the door/large hinge attached to wood panel glued down and dowels glued through and down into the foam
-cosplay type of foam to cover bend at the bottom.
-half circles (pearl color) used as rivets from the jewelry section at hobby lobby pictured above.
-Handle on the door 3D printed from Thingiverse, there’s a lot of other parts that has .STL files that can be requested from a member of SaltLakeGB’s through their ECU post.

-The handle that activates the green light is made of square and round dowel screwed together

The rest I got off Amazon as follows:

SYLVANIA LED Green Glass Filament A19 Light Bulb, Efficient 4.5W, 40W Equivalent, Dimmable, E26 Medium Base - 1 Pack (40303) https://a.co/d/1RuerQV

Baomain Voltmeter DH-670 DC 0-5V... https://www.amazon.com/dp/B01HO1T44U?re ... b_ap_share

Eowpower 2M 40Pin 40Way Rainbow... https://www.amazon.com/dp/B079KQ6K3Y?re ... b_ap_share

Lithonia Lighting VW150I M12... https://www.amazon.com/dp/B004QXRWPS?re ... b_ap_share

Baomain 16mm Push Button Switch... https://www.amazon.com/dp/B01N2T2LJI?re ... b_ap_share

Etsy-FannStar- for ECU stickers

Electronics… my husband custom built from scratch, NO Arduino Unit, there’s no formal diagram for it yet.

I used the same rubber strip gasketing that Saltlake GB used in their GB fan forums post to surround the back of the trap holder.



Here is my ECU’s new digs till the next event.

Image
Image
Image
Hooligan404 liked this
By jle2199
#4986123
This is pretty awesome, could you link me to the gasketing for the trap box, please, or do you know what it is still?
    Charlesworth Dynamics Trap Build

    Hi All, The Trap is coming on, I've nearly finish[…]

    I found a cool tube at Ollies discount outlet, and[…]

    Finally got my copy today - It's not the worst I'v[…]

    I don't remember exactly, But I think I've had pr[…]