User avatar
By tk1495
#4973001
Does the length of the tubing matter or just until it looks correct?
User avatar
By tk1495
#4973024
like from the straights to the elbows or from the injectors to the bottom of the pack or from the ppd to the resistor etc.....
User avatar
By tk1495
#4974052
Been a rough couple weeks.... have had multible surgeries and finally getting to the point that I can work again.

So where did I leave off?

Think I was working onthe different tubing on the outside of the pack, well that still is not done, think I cut some to short so ordered some more from GBfans.

Decided to get to work on the Wiring on the inside of the pack.

Put my Spangler plate on

Image

and laid everything out to make sure it all fit correctly

Image

I then realized that I needed to drill out the middle hole on the spangler plate for my Ninjatunes power switch and since it was attached I needed to do it in place.....

Well bad move

Image

The plate snapped! I reached out to Nathan to see about buying another one and he asked for a picture. Less than a week later I received a replacement plate from Nathan on his dime. AWESOME CUSTOMER SERVICE!!!!!!

So with new plate in hand I continued with my electronics installation

I ended up having to move the small board as it was hitting the pack when it was on. but got everything wired. Now working on cleaning it all up and making it look pretty.

Image

Those that have a CSProp shop Nfilter smoke kit and Ninjatunes kit this is what I needed to do, to make it all work together.

Image

I put a splitter on the battery lead with a power jack socket. Had the positive from the smoke kit go into the ninjatunes board vent port and added a wire from the ninjatunes board to the sockets positive terminal. I took the negative directly from the smoke kit na dput it into the negative terminal on the socket. I have not tested it yet as I have not put the shell on the MB completely yet so hope it all works. I did test the charging of the talentcell and the lights and sounds of the ninja tunes kit, WOOHOOOO I am geting more and more excited.

SO I also got my new bumper and shock mount and and got them put on

shock mount is mack factory, bumper is GBfans

Image

Image

Image

I do like the GBfans bumper more than the BOK one, it just fit better and the size looks better.

Image

Image

I also received my TC thrower kit and laid it out next to my BOK kit

Image

It looks so much cleaner and "simpler" to put together.

I still plan on building the BOK wand as well but just putting hte handle in the TC kit was so much easier than the BOK one.

Image

I did notice that the ninjatunes bargraph was not going ot fit in the TC space, to thin and long for it plus there is a ridge inside that whatever kit the TC is made for sits on.

Image

SOOOOO first mod of the TC kit is going to be to make the ninjatunes bargraph fit.

I marked off how much longer the opening is than the bargraph using it as a guide

Image

Image

I split the difference between the top and bottom while making sure it still sat on the ridge to screw it in.

Image

Then filled it in with black milliput

Image

and let it dry and harden.

I opened up the side a little and filed everything smooth. I then ground the ledge down, little by little until the bargraph sat in the hole.

Image

Image

Image

I may grind the ledge down just a bit more so that the bargraph is completely level to may just make a small bevel out of milliput to give it the correct look.

The next easiest thing looked like the handle. In his build thread it says to put the handle in and on the inside trace the edges then cut the tube where you traced.... I can not find the picture I took withthe handle in from the inside but I traced it and then proceeded to cut the tube with my drimel

Image

Image

I then deburred it and files it a little smoother rounding the edges

Image

Then test fit it back in. I have not glued or screwed it in place yet, I want to be able to work around that area without the handle being in the way.

Image

I am still waiting on my metal parts from BOK that I ordered when i received my kit, he said they should be here by the end of the week. It included the metal trigger and a metal heatsink for this as well as a metal shock mount which I no longer need since I got the Mack factory one.

The TC kit did not come with a trigger or acrylic tube so I am in stand still for that part until I order a different one or wait for my BOK one.

I am going to order the tube from GBfan and might order all the side discs and bangos as well for the thrower. Heck if I dont see them soon I might just order the trigger and heat sink as well.

I like the TC kit for the fact that all the pieces are seperate and you can get metal ones to replace the resin ones.

I did send a message to Justin but has anyone else used a GBfans aluminum gun track on the TC kit?
By tobycj
#4974054
Did you specify the larger metal trigger tip from BoK? He does two sizes, his "standard" one only fits his clear tube, which is smaller than everyone else's, so be aware of that.
User avatar
By tk1495
#4974056
I did not and did not know that as he never told me….. thank you for the heads up
tobycj liked this
By tobycj
#4974065
You'll probably find the BoK clear tube is too small for the TC kit as well, I think his are 20mm diameter from memory, rather than 22.225mm (7/8").

I swapped my BoK bumper for a gbfans one too, definitely the right choice!
User avatar
By tk1495
#4974189
Anyone know if the GbFans aluminum gun track will fit on the TC kit?
User avatar
By tk1495
#4974635
incase anyone else was wondering.... may fit but needs a plate.. as it is just the track

She doesn't turn 17 until the tail end of June 202[…]

Gbfans light kit DOA ?

It gets better. When I power the sound board by i[…]

Maybe a hot take, but I'm not sure if there are […]

Oh HELL yes. I'm in. I won one of the first on[…]